Tobi A

Do you need wireless if they are just sat around a table? Mics on desktop stands not an option?

Does anyone know the part number for the faders on a standard cl-12? I seem to recall they were ALPs faders. 
Hoping to order a a replacement without having to open it up first..

I have a set of microsones that I haven’t used in the field but on testing 2 things I found that could be problematic- the delay Bluetooth introduces and I couldn’t get as much level out of them as on phonaks. Not sure how they would go in louder environments for this reason. 
As always you get what you pay for!

I had the same problem, sent it off to get repaired.

I think it's the spring that pushes up the battery terminals inside the unit that needed replacing.

I've found you can just squeeze a MKH70 70 into a Rode blimp with a low profile xlr connector (cable techniques). I don't use the MKH70 much so didn't want to spend the $ on a rycote.

Good to know, I've been using an adaptor also

Absolutely, I've been using the  txAdvance app which is excellent 

Yep following rules 1-3 which is working pretty well, just trying to get that extra 5%!

Good point about the potential broken SMA.

I'm thinking of adding some inline RF attenuators to my links/hops transmitters in my bag setup, to help my recievers out with spray etc.

I'm using smqv and the min power output is 50mW, I think half that or even less would be enough from my bag to camera which is usually close.

Has anyone one done be this? I recall a discussion somewhere but can't find it now.

How much attenuation would I need? 5db, 10db? If anyone knows the formula that would be amazing!

I might have of missed it, but what happens when the battery in the earpiece needs replacing after several years? Do I send it back to manufacturer or will I just buy a replacement earpiece?

Proaims soundchief looks like a direct copy of a Rastorder Foldup cart http://www.rastorder.com.au/product_foldup.htm

Hey Ed, I've been using one of these with no troubles https://www.ebay.com.au/itm/322165403845 

I went with 15 volt so I can have both it and a smart battery plugged into my PSC triple play BDS. The BDS uses the source with highest voltage so if I lose AC power it switches to my battery.

20 minutes ago, Turi soundfish said:

H Tobi. 

Of course, you have just to click on "Upload all files" and the Viviana Cloud app will select automatically all the files present into the folder and it will start uploading.

Thanks

Can you select and upload a folder though, like In your example the folder named 20Y11M20. Or if uploaded the folder AON-TEAM-A will the sub folders and files also upload?

Can you select entire folders to upload rather than individual files? In the demo video it doesn't seem to show this? 

I've tried using dropbox and google drive apps and directly connecting to an 833 and that was a major drawback for me, having to create the folders then adding files to them on the cloud.

Thanks for the replies, I think I'll just run seperate batteries for now.

My set up is Lectrosonics SRC (also tried 411a) feeding 833, both powered from remote audio BDS and Audioroot battery.

I'm getting a high pitched hum/whine when I use the Aux channel 7/8 input on my 833. Problem stops if I power SRC from its own battery using the Battsled so Im guessing its a ground loop.

Anyone else experienced this? Can I disconnect the ground between the SRC and 833 input? Should I get a line isolator like this - https://www.radialeng.com/product/icecube?

Fingers crossed for an android mobile support in the next release!

Thanks for the chart, very handy. Yes 22 or 24 awg will do the job.

Yes I've ordered something similar to try.

Looking at the remote audio smart battery cup (https://www.trewaudio.com/product/remote-audio-bdshqcs2/) looks like it says 20awg, but the only 4 core 20awg I could find is only 6mm thick!

I don't think any of their multi core cables would be heavy enough gauge, 833 can draw up to 1 amp. Also doesn't need to be shielded.

I want to make some power cables to an 833 from my smart battery. Any recommendations on a source of 4 core dc power cable? Needs to be 4 core to carry power and battery telemetry.

Yes thats what I thought I'd do. So Sleeve = Ground and ring = Hot. And Tip = disconnected?

I'm making them for someone else and don't have any Sony wireless to test it so want to get it right!

I'm about make some line level input cables for Sony UTX-B03 UWP-D body pack transmitter.

I've found some info on wiring for mic input but not line level, not sure if its the same?

4 hours ago, TristanChaika said:

 

Do you know how to tell which way a cable is wired if you already have the cable?

 

If a cable is wired incorrectly, could it still sound OK, but eventually damage the camera?

You'd need to check with a multimeter or open the connectors and have a look. If incorrect it wouldn't damage the camera but there is a possibility the phase is reversed . 

On 12/28/2018 at 5:52 AM, Fred Salles said:

Hey, I just want to make sure that the pin wiring of their TA3 audio in is standard? (1ground, 2 hot, 3 cold)

I am making the cable for a friend but don't have the camera to test it. No details on the cam user manual of course...

Thanks anyone who has tried own cable for the confirmation.

I made some cables recently and emailed Black Magic to check: