Jump to content

sergiofucchi

Members
  • Posts

    266
  • Joined

  • Last visited

  • Days Won

    1

Everything posted by sergiofucchi

  1. You can buy also the Rycote modular Windshield Kit 3 (30mm, No CB) - Product Code: 086071.
  2. sergiofucchi

    wingman?

    No. The problem it is another.. If I try to enable a track in 633 but I have not done this in the app, track remains disabeld.
  3. Hi. I have a problem to use the Sanken CUB-01 with the transmitter Wisycom MTP-40S. Does anyone have any suggestions on its connection mode? Thanks.
  4. sergiofucchi

    wingman?

    The only thing I find wrong is the impossibility to arm a track if it was not enabled in the app.
  5. Because its belt transmitters have the possibility to vary the emission power from 10mW to 100mW and because his receivers are true diversity receiver with four receiving modules, one for each antenna and each channel. Also with just two transmitters I can cover the entire range from 470MHz to 698MHz.
  6. I put in a Wisycom instead of a Lectrosonics. I sold a Lectrosonics kit and I'm going to sell also all the rest of the equipment to change to Wisycom.
  7. Hi. Has anyone tested the 4017 on the background noise using different preamps?
  8. Schoeps says no: only one of the two output channels can be transmitted. Only pre dsp or only post dsp.
  9. First image is my SPS200 setup for ambient and/or nature sounds. The other is my light setup.
  10. I do not think. Plug on has a connector XLR with three holes for mono and for stereo it has five holes. But two channels out of SuperCMIT use a single XLR mono connector where on pin 1 it comes from dsp and on pin 2 not.
  11. I own a Schoeps SuperCMIT 2U and this is a great microphone in interior and outdoor. It is a little difficult to position using the 2-position in dsp, especially when fast moving the pole, while 1 in that there are no particular problems. Unfortunately for this application must use the wire or plug on Zazxcom, bearing in mind, though, that you can only use the output from the dsp and not also the analog output. In connection with the wire instead you have two output channels: one from the dsp and another bypassing the DSP, as a simple CMIT 5U. I got good results even from the DPA 4017B, compact and lightweight, very incisive from a distance.
  12. Good morning. After a long time I'm back with some comments on the microphone Soundifield SPS200 I purchased some time ago. I bought the kit 1, ie only the microphone and cable. Later I also bought the flexible short wire to reduce noise when mounted on windshield suspension. Now I use it in a Rycote WS2, I already had, with the hard gray Lyre and I am quite well. I have one doubt, and that is whether the fact that two capsules are quite close to the junction of the anterior dome of the windshield and therefore fail to capture well the sounds that come from that direction.
  13. When adjusting the trim / gain using the appropriate potentiometer for input 1 - 2 - 3 it would be useful it were also shown the value in dB for the mic and line inputs as well as with the digital inputs. Sergio.
  14. I can not I use my RT-UMK-100-RF with my 633 (1.04). Yet with my 788T it works very well: It is strange that SD handle in a different way the interfaces usb keyboard in its products. Sergio.
  15. Wysicom can receive Lectro. This is that has said Wysicom during a day dedicate at their products at Cinecittà in Rome about three week ago.
  16. Next September I will be in Greece, in the village of Pyli, for a set and I would like to know what are the restrictions on the use of wireless microphones in that area. Next spring, also, I have to go in Japan (Osaka) for another set and even there I would like to know what limits are there.
  17. is a bit of time that I do not come here anymore. Now I have purchased a used LM1 kept in good condition. I noticed that the power supply comes with 26 V dc but usually on the cart I use a battery of 12 V dc. Once connected the mixer to battery, the mixer is turned on even if the battery test shows a very low value. I still have not got to test it, but the previous owner assured me that even at 12 V dc the mixer works. My concern is that with a lower voltage than the nominal distortion may increase. What do you think about that?
  18. I use this http://www.panasonic.com/business/provideo/BT-LH910GJ.asp but it is little expensive.....
  19. I also bought one of these, one from 240/960 MHz I have updated it with the firmware v.1.11. But in the pdf manual that I downloaded from the website it is not very clear, at least to me. I use a Lectrosonics system on the blocks 19 and 20. What should be the parameters to set the RF Explorer to have a correct view of the situation? Sergio
  20. I have a Canare DA206 but it is very heavy for a length of 5 meters. I sot searching for the best cable that is also lightweight and flexible enough to be lighter on the boom.
  21. I'm looking for a good digital microphone cable 110 ohm aes / ebu to connect my Schoeps SuperCMIT from boom to my 788T. It must also be relatively light and flexible. Any advice? Sergio.
×
×
  • Create New...