Alex Altman Posted January 12, 2009 Report Share Posted January 12, 2009 Hello all, I have a question regarding a recent issue with my Mackie M2600 power amp. After not using the amp for a couple months (and everything working fine before, except for one side of the unit), I get a playback gig and have a sound quality problem. The sound had an extreme amount of high end that I had never heard before. And when I say extreme, I mean like painfully brittle at high volume. The rest of the sound seemed to be in tact however; lows were full and mids were fine. The highs weren't distorting either, they just seemed to be boosted beyond explanation. My solution for that particular show was to just tape some foam over the tweeters. Ugly, but it worked. I am assuming it is an amp issue because I have traded out the playback device, cables, and mixer with no change in sound. The two PA speakers also sound identical, eliminating a speaker issue in my mind. I can't imagine the two speakers going bad the same way, at the same time. Any ideas? Is this the slow death of my Mackie? Or is it something completely different? Thanks! Quote Link to comment Share on other sites More sharing options...
John Blankenship Posted January 12, 2009 Report Share Posted January 12, 2009 Alex, Do you mean that one channel has the extreme highs, both channels, or that one channel is completely non-functional and therefore rules out comparing them? There are switches on the back for low-cut filters and others to set up crossover frequencies to drive separate parts of a stack. Only guessing here, but you may have them in the wrong position(s). http://www.mackie.com/support/downloads/manuals.html JB Quote Link to comment Share on other sites More sharing options...
Alex Altman Posted January 12, 2009 Author Report Share Posted January 12, 2009 Hi John, thanks for replying. One side is completely non-functional because of a short somewhere. A local Mackie authorized repairman here said he couldn't find it. I just don't ever try to use it anymore. I do know about the filter switches on the back of mixer, but the thing that confuses me is that while the high end is super loud, the rest of the signal seems to sound fine. The low end will thump for instance, but shouldn't it be almost non-existent if a low-cut was enabled? Quote Link to comment Share on other sites More sharing options...
John Blankenship Posted January 12, 2009 Report Share Posted January 12, 2009 That would really depend upon the crossover or low-cut curves. They may show them in the manual. JB Quote Link to comment Share on other sites More sharing options...
Scott Clements, CAS Posted January 12, 2009 Report Share Posted January 12, 2009 Just one thought on only one side working. Make sure the "amp mode" isn't in mono, or bridged. Sorry if that's to obvious, but just thought I'd mention it. scott Quote Link to comment Share on other sites More sharing options...
studiomprd Posted January 12, 2009 Report Share Posted January 12, 2009 " everything working fine before, except for one side of the unit " wow, that is an oxymoron! and a tech told you the problem is a "short, but he can't find it" ?? it is probably more than just "a short", something is wrong with it. unfortunately, 2 channel amps rarely have 100% independent channels, and the additional symptoms you describe do not sound like user switch settings problems, except for possibly putting the amp into single channel mono mode (see, the 2 channels have to be interconnected inside!) it could be in the speakers or speaker wiring: did you try each speaker and wire separately?? if that isn't the problem, it is broken, and needs to be fixed by either Mackie, or a Mackie authorized service center. Quote Link to comment Share on other sites More sharing options...
Glen Trew Posted January 13, 2009 Report Share Posted January 13, 2009 Bring it in, Alex. We'll figure it out. gt Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.