Matthias Richter Posted July 31, 2016 Report Share Posted July 31, 2016 one of my LA2.6 stopped getting audiosignal. Checked the lav, checked the gain setting, did a Factory reset. Any more to check before I send it in? Quote Link to comment Share on other sites More sharing options...
RadoStefanov Posted July 31, 2016 Report Share Posted July 31, 2016 I have never experienced this exept when the limo craps out Quote Link to comment Share on other sites More sharing options...
Matthias Richter Posted July 31, 2016 Author Report Share Posted July 31, 2016 there is no crackling. Nothing. Just silence. Was on an actor this morning for 5min before it went dead Quote Link to comment Share on other sites More sharing options...
Tong0615 Posted July 31, 2016 Report Share Posted July 31, 2016 I experienced once, QRX100 got radio signal but no audio, after reboot everything was fine. Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
Matthias Richter Posted July 31, 2016 Author Report Share Posted July 31, 2016 if I crank up the gain all the way to 52 and blow into the lav I can hear "something". Seems hardware. Quote Link to comment Share on other sites More sharing options...
John Blankenship Posted July 31, 2016 Report Share Posted July 31, 2016 With what Rado said, check the pins in the Transmitter's Lemo connector. It has been known to happen that a pin gets pushed down into the connector housing and no longer makes proper contact. Quote Link to comment Share on other sites More sharing options...
Matthias Richter Posted July 31, 2016 Author Report Share Posted July 31, 2016 Thanks for the tip! Just checked and all 3 pins are on show right on the top of the housing. Quote Link to comment Share on other sites More sharing options...
Reuben Colazo Posted July 31, 2016 Report Share Posted July 31, 2016 If the transmitter shows normal audio levels with a lav plugged in, and the qrx shows signal strength but red light ln the antenna status, it may be your synth chip. Mine went out earlier this month in my trx900LT, factory reset actually screwed me because I had a work aound but after the factory reset it would not work at all. Quote Link to comment Share on other sites More sharing options...
efksound Posted July 31, 2016 Report Share Posted July 31, 2016 IMHO The best and easier way would be to try with another lav to be sure if it is the lav or the TRX. Quote Link to comment Share on other sites More sharing options...
soundtrane Posted July 31, 2016 Report Share Posted July 31, 2016 3 hours ago, Matthias Richter said: Thanks for the tip! Just checked and all 3 pins are on show right on the top of the housing. hear, but don't listen to Rado all the time Quote Link to comment Share on other sites More sharing options...
Matthias Richter Posted July 31, 2016 Author Report Share Posted July 31, 2016 1 hour ago, efksound said: IMHO The best and easier way would be to try with another lav to be sure if it is the lav or the TRX. thats what I did first of course! Because normally it´s the actor ribbing the lav of or something. No "luck" this time. Howy´s sent me an email how to load the settings from that receiver´s SD-card. Will try 2moro. Quote Link to comment Share on other sites More sharing options...
Jason A Posted July 31, 2016 Report Share Posted July 31, 2016 6 hours ago, Reuben Colazo said: If the transmitter shows normal audio levels with a lav plugged in, and the qrx shows signal strength but red light ln the antenna status, it may be your synth chip. Mine went out earlier this month in my trx900LT, factory reset actually screwed me because I had a work aound but after the factory reset it would not work at all. This happened to me as well. Exact same issue with the synth chip. Had to send in to Zax to fix. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.