M Sisco Posted March 29, 2017 Report Share Posted March 29, 2017 I used a Sennheiser G3 wireless kit as a camera hop to a Canon C100 the other day. This was the second shoot for the unit on the camera. It rained. We covered the camera, but no one is perfect. It could have gotten some moisture where it shouldn't be. Everything appeared okay when I got home and checked the gear. Today I pulled the G3 out again and couldn't get a decent input level on the mixer. I took it home and tested it in my 552, then direct to a 744T and again with a DR100MK II. All of them had extmely low input levels and the signal sounded like it was on a high pass filter of at least 400Hz. I tested with two mics. Both the same. I reset both the transmitter and receiver to factory. Same. Any insight before I schedule a repair? Quote Link to comment Share on other sites More sharing options...
Rick Reineke Posted March 29, 2017 Report Share Posted March 29, 2017 Put it in a jar of rice for few days. Sometimes that will draw the moisture out of a device. I assume you double checked the Rx 'AF output' and Tx 'sensitivity' settings. Do the meter(s) on the system show normal deviation? Quote Link to comment Share on other sites More sharing options...
Tom Duffy Posted March 29, 2017 Report Share Posted March 29, 2017 Rice is no good, that's a myth. Silica gel packs are much better. https://smartphones.gadgethacks.com/how-to/myth-debunked-uncooked-rice-isnt-best-way-save-your-water-damaged-phone-0154799/ Quote Link to comment Share on other sites More sharing options...
Philip Perkins Posted March 29, 2017 Report Share Posted March 29, 2017 If it's acting that weird then I'd forget the home-cures and send it to be be fixed. It's a bummer but you want to be able to rely on it, right? Quote Link to comment Share on other sites More sharing options...
Rick Reineke Posted March 29, 2017 Report Share Posted March 29, 2017 Thanks Tom, Silica gel packs then. DO NOT EAT Quote Link to comment Share on other sites More sharing options...
chrismedr Posted March 29, 2017 Report Share Posted March 29, 2017 what also helped me once was putting a moist device on a heating radiator for some days (just normal heating level in winter). but I second Philip, if it's going to be used on important stuff in the future better to have it checked then risking that the problem might come back in a tricky moment. chris Quote Link to comment Share on other sites More sharing options...
David Waelder Posted March 30, 2017 Report Share Posted March 30, 2017 I'm insufficiently familiar with the specifics of Sennheiser G3 packs to know if opening the case is possible but that's a good first start to any water intrusion issue. An actress once inadvertently dropped a Lectrosonics pack into a toilet and I was able to avoid serious damage by pulling the circuit board from the case so it could rapidly dry out. That's relatively easy with the Lectro - just two screws on that model pack. If removing the circuit board or completely opening the case is not possible, opening the battery compartment would probably be worth doing. David Quote Link to comment Share on other sites More sharing options...
Derek H Posted March 30, 2017 Report Share Posted March 30, 2017 It's very easy to disassemble a G3. You'll need a Torx screwdriver set and there's a couple ribbon cables you'll have to disconnect but nothing difficult. There's two main boards in there. There are many YouTube videos if you want to see a tear down. Quote Link to comment Share on other sites More sharing options...
resonate Posted April 1, 2017 Report Share Posted April 1, 2017 It might be a good idea to get one of them Sennheiser pouches for some rainy future : http://www.pinknoise-systems.co.uk/sennheiser-bpp-beltpack-bagpouch.html Quote Link to comment Share on other sites More sharing options...
M Sisco Posted April 1, 2017 Author Report Share Posted April 1, 2017 Thanks for the replies. Some silica gel is definitely a good order item. It did clear up a little from simply drying out. I learned that from the time I dropped the phone in the John. However I think some mishandling from the camera department was the culprit. Picked up a new 1/8" to XLRm cable and it came right back to life. Soundman mantra: check the cable first. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.