Do It Yourself
for those who are brave enough to go it alone... with a little help from your friends
817 topics in this forum
-
- 2 followers
- 5 replies
- 1.7k views
Thinking about adding a second battery connector so that I can hot swap batteries without bringing the bag down. I was considering using diodes to isolate the batteries, but I don't want the voltage drop that would bring. Do I even need isolation? I don't want to run both batteries at the same time, just connect a second then disconnect the first.
Last reply by Derek H, -
- 3 followers
- 8 replies
- 2.4k views
Just a quick showcase of an idea I've been toying with lately. I'm thinking of this as a sort of sub-distro and it will hang off the main BDS (or could easily be stand alone if need be). It's a pretty simple device; just a poly fuse on each output.
Last reply by Lucas, -
- 14 replies
- 7.1k views
Just was wondering if anyone has any experience with soldering different connectors on the Sanken CUB-01. Im thinking of just buying it without any connectors and putting my own 3pin XLR-M. Is there anything in particular to look out for soldering wise? Or is it just straight forward 1 to 1, 2 to 2, and 3 to 3? As far as XLR is concerned.
Last reply by AlexQ, -
- 4 replies
- 1.2k views
Hello everybody ! I have an issue with the plug of my headphone. The plug remove accidently and a part of it stick inside the connector for headphone. I cant extract it easely... If i open the Nomad can i have an easier access to the plug from inside ? Thank you to answer !
Last reply by tourtelot, -
- 1 reply
- 1.1k views
I've been micing singers for operas over the past couple years, using lectrosonics transmitters with DPA 4071s. Does anyone have experience with Leukoflex? Is it preferable to 3M surgical tape? Thanks, B
Last reply by nickreich, -
- 1 follower
- 24 replies
- 8.1k views
Made for Jan McLaughlin.
Last reply by Eric Toline, -
- 0 replies
- 865 views
Hey all - Has anyone discovered a way to mount a 5/8 baby pin on a standard 19" rack (which uses 10-32 screws)? I'd love to add a monitor arm to my Yamaha 01V96i mixer rack, but I can't seem to find a way to mount one on the rack rails. Thanks! -Mike
Last reply by Mobilemike, -
- 2 replies
- 1.4k views
I've heard that you can get Comtek to mod M-216 transmitter to have the BNC antenna connector so it essentially becomes an Option P7. Has anyone done this mod themselves? How do you open the transmitter case without breaking it. Does anyone know the part number for the BNC connector?
Last reply by John Blankenship, -
- 5 replies
- 1.7k views
I have some cables that are balanced 3.5mm jack to female XLR that I used for old RED cameras with 3.5mm audio input jack (why oh why RED?). One of the 3.5mm jack broke so I cut it off and stripped back the insulation to replace the 3.5mm jack and what I discovered has me baffled. Inside were 3 conductors as you would expect, but they don’t seem to be insulated in any way from each other. I am so confused as to how the cable works when the conductors are just running together with nothing separating them. Can anyone with electronics knowledge explain how this would be possible? Perhaps a coating? But even so it would be very thin and prone to failure I imagine. Never has …
Last reply by tourtelot, -
- 6 replies
- 2.8k views
hi all, for a wildlife documentary, i am researching possibilities for longtime mic-installations in full out weather... as this sounds like quite a contradiction, i wonder if anyone of you has experience to share regarding this topic. the mics ( at least the capsules ) will be high up in trees, installed by crane, as are some endoscopic cameras. everything is cabled down to ground for signal, powering etc. once breeding season starts, we cant get close anymore. i am posting in the diy section, because i think the solutions from the shelf will not work here....
Last reply by mateuf, -
- 1 follower
- 2 replies
- 1.5k views
Curious if any of you guys have found any unexpected "household" items that can be repurposed somehow for live sound applications (ie. on the road, in the shop, load in, etc). Always on the look for useful hacks! Thanks
Last reply by Dalton Patterson, -
MixPre knob
by mrkva- 10 replies
- 7.8k views
Designed and 3D printed a "knob extender" for my MixPre-6. Even thick headphone jack connector still fits, but the knob has a better grip and is easier to reach when operated in a bag. Download the .stl file (for 3D printing) here: http://knowledge.lom.audio/research/mixpre_knob Or get it from our company here: https://lom-label.myshopify.com/products/mixpre-knob
Last reply by Janik Hampe, -
- 18 replies
- 10.3k views
So, I recently acquired a Nagra III, and was wondering if anyone had access to a service manual (not operators manual). I suspect a re-cap is in order, but I could have larger problems as well. Everything runs fine in rewind, but in PB and Rec, the motor winds itself down after exactly 10 seconds. Beyond that... Biasing, modulometer calibration, yada yada yada Thanks in advance! Wyatt
Last reply by PiO, -
- 2 replies
- 1.4k views
I've recently picked up an HMA for a project and will be making a couple low profile cables to go from the mic end to the plug on which will be at the top of the pole. Whats your preferred cable gauge for this? Already have some Canare L-4E6S, but was considering a thinner gauge star quad cable for an even smaller profile. Would the thicker cable gauge provide better shielding against potential RF interference? Im sure it has its plus's for being more resistant to wear and tear. Curious as to what others have been doing.
Last reply by Dave Pullmer, -
- 7 replies
- 2.9k views
Hey everyone, Can anyone shed some light on proper grounding techniques when wiring up a sound bag? Is the usual one-path-to-ground rule still the best approach to constructing a bag that is as quiet as possible? Perhaps centred around the mixer/recorder with the shields floated at the receiver end?
Last reply by mikewest, -
- 1 follower
- 7 replies
- 2.7k views
Hi, Here is my DIY BDS. It has 5 switches which are wired like this : 1) Master switch : activate all the other switches + voltage/current display + back usb output (to charge tablet/phone for wingman) 2) one Hirose for recorder 3) two Hirose for wireless mic and IFB 4) One hirose + one DC jack for video monitors and other stuff 5) One USB output (for a small light or a fan : I live in west Africa) It has 2 inputs : -1 hirose -1 dc jack I am mainly using modded Talentcell battery, so I can use and charge the battery at the same time. The voltage is regulated at 12V. Each output is…
Last reply by drpro, -
- 1 follower
- 5 replies
- 1.9k views
I want an RX Emergency Two to use with my 302, but can't justify the $200 cost. I looked at the tech notes from Sound Devices about connecting to the mix in, but don't know how a variable resistor will interact with the resistor network they recommend. I decided to compromise and build inputs that would connect to the camera returns; this way my controls are "faders" and the trims on the 302 are "gains". Plus I can change the channel 4/5 signal routing in the 302 and not have to add external switches. The box is incredibly simple; Neutrik combo XLR/TRS input jacks, Bournes 10k log taper pots, and a 3.5mm output: …
Last reply by Philip Perkins, -
- 11 replies
- 2.4k views
..a few pics of a recent little DIY project... Got a CMIT. I didn't feel like buying a new basket/windjammer, and hauling two around, so I DIY'd the parts I needed. The old black one on the left held the 416. The newly minted one next to it holds the new lime flavored CMIT. The durometer of the rubber bars was a trick to match, and I broke it three times in search of an adhesive that would bond the rubber bars securely to the nylon and aluminum (I'll skip the aluminum on the next one). The two rails are made of thick walled stainless steel tubing, and are seriously strong. All of my mismatched 1/4"-20 set screws bug me. The wind's howl…
Last reply by Rachel Cameron, -
- 1 follower
- 10 replies
- 3.6k views
What cable do you use for making proper tc cable? I have best results when using mic cable from a multicore I don't need any more. They work best on the lemo side but i struggle sometimes to get it nice on the bnc side. To solder the shield on the bnc shell works but doesn't look nice. Using a 50 Ohm bnc works well on that connector but sucks soldering on to the lemo 5pin... Best regards!
Last reply by Philip Perkins, -
- 1 follower
- 7 replies
- 1.9k views
Hi All, I want to make an dolly extension for my Beta cable system not including fan tail. OSC 8 on each end running from my 18" camera fan to drivers end of the dolly. Any suggestion on the "perfect" catch all length? Was thinking about 8' or 10' but thought I'd check with the communal knowledge base here for suggestion first. Thanks
Last reply by stacysound, -
- 3 followers
- 35 replies
- 27.3k views
Anyone here assemble their own Lemo connectors for Zaxcom wireless, or any other Lemo connectors? What all is needed for tools? www.matthewfreed.com Production Sound Mixing for TV, Films, and Commercials
Last reply by Derek H, -
- 3 followers
- 43 replies
- 19.7k views
I was looking for a cheap cart that can fit all sorts of types of work. I found the rolling workshop of STANLEY, they have several models and sizes that one could fit my needs. Most of the time I work with Harness so I chose this model because it is modular and can be used for all kinds of jobs. Improvements: I add small wheels in the front. I'll find something better to the antennas.
Last reply by Dejan Ceko, -
- 8 replies
- 3.2k views
Hello everybody I'm a freshly owner of a wonderful Nomad 10 ! I bought it used and the battery to maintains clock is dead... I'm very affraid to open the nomad... I saw a post about this topic but the photo is not enough to understand how to do... The xlr input is gone ! Maybe somebody from here can shoot a video about the disassembly ? It will be very very nice ! Thank you so much !
Last reply by John Blankenship, -
- 5 followers
- 29 replies
- 9.8k views
Can anyone suggest an off-the-shelf right angle (adjustable) TA3F field-serviceable connector that doesn't require an endoscope and a mechanical engineering degree to deploy? Have tried two versions from Usual Suspects, very expensive per each, hated them, to big too fragile too fussy. This is for a bespoke setup so I need to solder them myself (re a Kortwich commission). Is the only solution to hack up straight connectors and epoxy them up? I'd like something that I could change the cable-exit angle on in the future, as well as repair if they get damaged. thx
Last reply by dactylus, -
- 10 replies
- 2.2k views
The end cap on my venerable 416 has pulled off a couple times when removing a softie. What would be the best thing to use to glue it back on without it being a permanent bond or messing with the sound. Thanks, Bob
Last reply by Robert Buncher,
