Do It Yourself
for those who are brave enough to go it alone... with a little help from your friends
814 topics in this forum
-
- 12 replies
- 10.4k views
I'm wiring a 5 pin XLR female to a 3.5 mini TRS female so that I can have stereo (left / right) in the female TRS for a headphone feed. I wired the 5 pin as: Pin 1to sleeve of TRS Pin 2 to tip of TRS Pin 4 to ring of TRS Pin 3 and 5 I tied both into the ground of pin 1 When I tried this I was getting signal to the headphones but there was a lot of noise. What am I doing wrong?
Last reply by Erick, -
- 1 reply
- 2k views
First off I want to give a big thanks to Mike Van Tine- he was a big help with info on how to do the 3047 card install on an older mother board... I've said it before: he's a go-to guy! All I had to do was cut 2 board traces, add a shunt wire and a 10k ohm resistor & it's good to go... Of course, my wife kept looking over my shoulder & pronouncing me wacko: "brave man, maybe not too smart- but brave". Hey- it worked... now it's time to install the 4-pin Hirose power connector. I was tempted to put in a 4-pin XLR, since there's plenty of room, but the Wendt X3 is also 4-pin Hirose & I've decided to standardize on that. John Here's a pic:
Last reply by John Steigerwald, -
- 4 replies
- 2.1k views
Greetings all: I have a simple technical question: I'm finally wiring up some camera return adapters for my 788T/CL-9 Sound Devices setup. The 2 returns on the CL-9 are line level balanced XLR inputs. Camera return will be on an unbalanced stereo 1/8" TRS connector. What would be the appropriate wiring for the TRS 1/8" female to XLR male cable adapter? Thanks! -Adam
Last reply by Adam Jones, -
- 10 replies
- 2.7k views
Hi All, Attached are a few pictures showing a cable I bashed up, it was mostly "GID" (get it done) and a bit of DIY. I needed to record 5 channels of house wireless (dialog + solo singer) and the musical cue. My initial recce found the house mixer to be a Mackie configured for live sound (e.g., onboard effects, no direct outs) and the aux's were inaccessible due to routing issues. The ideal thing would, I suppose, have been a split before the board but this posed two problems: I didn't have 6 channels of split (relatively easy to solve) and, explaining why / obtaining permission to re-patch the mic inputs (much more difficult). Although the board lacked direct…
Last reply by Celac, -
- 5 replies
- 1.9k views
Hi everybody, I am lucky enough to grab mr Mondo Vilas used 208 mixer. I tremendous step up from my 106. But i hate the knob colors. I would like to replace the purple knobs for the Aux 1 and Aux 2 controls. 18 knobs total. Anybody here every replace their knobs? I'd go with the white or grey. Obviously, simple DIY project. Would love to go directly to the source not thru service company. If possible. Thanks, john
Last reply by johngooch, -
- 32 replies
- 9k views
There have been a couple of threads about building cart power solutions, but I couldn't find much in previous threads about which SLA batteries people had good or bad experiences with. I know a couple of folks like the 12v 33ah MK cells, and I know that Powersonic 35AH are an old favorite, but has anyone had the opportunity to do side by side tests of different brands? Or does anyone just have vaguely uninformed guesses they'd like to share? FWIW, I'm planning to build a couple to use with my PSC Powerstar on my new cart, so any thoughts are welcome. Thanks everyone, A.
Last reply by Jeff Wexler, -
- 0 replies
- 1.4k views
http://www.mutr.co.uk/autoheal I'm sure we will all find great uses for this new product. BVS
Last reply by BVS, -
- 3 replies
- 2.2k views
Saw this in my never ending internet browse. Not bad for 16 bucks, course you usually do get what you pay for. Still could be a decent addition to a kit as a backup. http://ossmann.blogspot.com/2010/03/16-pocket-spectrum-analyzer.html
Last reply by dfisk, -
- 7 replies
- 2.1k views
I have the cable that SD provides, but its too damn short. I have a section of RJ12 cable here and wanted to see if anyone had experience with this before I go buy a crimper. It looks to me like the C.Link requires a crossover type cable. Any experience or input would be greatly appreciated. I would contact SD, but they are out for the weekend and my shoot is sunday. I suppose if I don't get this sorted out I'll just link TC and WC on their own cables, but having matching header TC would sure be nice. Thanks in advance, Wyatt
Last reply by Wyatt Tuzo, -
- 10 replies
- 2.8k views
Hi all Does anyone have definitive wiring info to put together at TA5 to Stereoline input cable. Want to trim down my sundry cables with new 788T. I'm currently using adaptors to get where I need to be and was going to knock up something on the weekend Any info would be great Chris
Last reply by chris_bollard, -
- 1 follower
- 2 replies
- 3.4k views
I imagine this exists here somewheres but i cant seem to find it - does anyone have a diagram of the 8 pin assignments for both psc and remote audio breakaway snakes?
Last reply by Bob Marts, -
- 1 reply
- 1.8k views
did a mod to my 7506 and have attached a TB mic. I used a AudioTechnica Headset: http://www.thomann.de/de/audio_technica_athcom1.htm used the rubber thingy from the other side of the headset to fix the mic onto the side of my headphones. Works great with my Cooper TB input (dynamic in) and very cheap! Matthias
Last reply by Eric Toline, -
- 3 replies
- 1.6k views
I read somewheres that pin 3 should be tied to pin 1 ground, or floated all together for certain devices, saying that the cable can act as an antenna, etc. Cant seem to find an answer to one or the other as to which is best when wiring cables for senny transmits as camera links. Anyone have any insight? And on that note, any info on what to do with pin 3 in general umbalanced connections? kp
Last reply by Eric Toline, -
- 13 replies
- 6.5k views
Here's my latest project: a 9v power distribution box. Many factors led me to make this custom distro unit. 1) I use Audio Ltd and Micron radio mics, both of which want 9v external power. Microns say they'll take 7.5-16v ext power, but they say ALWAYS use their custom cable, which has a 9v regulator built in. And Audio Ltd specs say they'll handle 9-14v DC, but NP Li-Ion batteries at full charge will put out 16v. I don't have the luxury of the 10-18V range of Lectro's. 2) Of the off-the-shelf solutions, only Hawk-Woods has a 9v-regulated distro box. The BDS, from what I can tell, passes along whatever voltage it receives. 3) My Microns don't have a pilot tone to …
Last reply by bcopenhagen,
