Display Name

Dan, even I might actually have an unused Petrol harness, still in plastic bag in my storage. I’ll take a peek tomorrow and send you a PM if you like.

So was DaVinci Resolve once in a time as well.

I can see Aaton or Cantar as the audio brand together with CineAlta. Sony have the financial strength and it would solidify their cinema territory quite well.

BlackMagic have a penchant for buy left overs from closed businesses and open them for the masses. And they are quite empty on the dedicated audio recorder area.

I can recommend Trancends RecoveRx which is built on open source and testdisk but with a nice gui. https://www.transcend-info.com/support/software/recoverx

When running power over USB-C PD, all involved parts communicate and negotiate voltage and amperage. That’s power adapter, cable and device. So make sure you are using a usb-c PD cable rated with enough power you need. Could this be the reason you are seeing to lower voltage?

Unfortunately not. The old CF cards used ATA interface while the CFExpress uses multiple lanes of PCIe. The only thing they share are the first two letters. Everything else is totally different. But you could use a CF to SD adapter card and run the CF card with a SD card inside, instead.

I’m not even sure that some of their products actually will return from having their production suspended. I believe the A/D converter used in the mixpre 3 is actually EOL and not produced by Asahi Kasei anymore. Those used in the 6 and 10 are still in production. So either they need to find a compatible slot in, do a pcb redesign or vacuum resellers for it. The 833 was suspended as well I believe but I don’t know which converters they are using.

For angled 3,5mm connectors I’ve used the Neutrik NTP3 when I’ve done my own soldering. They are tight to put together but the quality of them and the result are top notch.

Here’s their compatible chart. https://www.varizoom.com/v/vspfiles/downloadables/battery-chart.pdf

Running the mini on 3 AAA of a higher capacity model will give you 3x1.2x0.9 = 3.24Wh of energy. Going with Sony’s NP-BX1 li-ion pack would give you roughly 4.5Wh.

Also make sure you are not in USB-C file transfer mode. Or perhaps try toggle it on/off and see if the phone reacts.

Rode have the Video Mic NTG with built in battery and can be used with both 3.5mm or usb-c as io interface. https://rode.com/microphones/videomicntg

Denecke's TimeCode Toolbox on iOS can display and output LTC as well as accepting input of LTC signal and display it. I tested it on an old iPhone SE and setting TC Toolbox to output LTC and then jam the USOne worked great. But on the SE the app did not listen to anything else but the microphone as input. Not sure why but it should work. Will do some more tests. Edit: might be I need to get a trs-trrs for this.

Looking inside the Updater app on macOS it appears as if the 2.0.9 firmware is present. <device name="UltraSync ONE" sig="*USone" deviceType="10" updaterIncRequired="300" autoUpdate="1" rstfs="0"> <file name="USone209.a32"/> <file name="TFPUs115.tcg"/> After launching the updater, it downloads newer firmware into itself. <device name="UltraSync ONE" sig="*USone" deviceType="10" updaterIncRequired="40509" autoUpdate="1" rstfs="0" stickerText="USOne"> <file name="USone214.a32"/> <file name="TFPUs115.tcg"/> I copied the USone209.a32 from inside the app to my desktop. I then choose Open from within the updater app and loaded the extracted firmware. The Update now lists the Firmware in the lower part of the window. But I've not tried to revert my USO to that firmware.

I have not updated mine yet so I can’t tell if they behave properly. Have you tried to apply the update ones again?

Alkaline don’t fancy that kind of load. If you instead went with IKEA Ladda 2450mAh which are IKEA branded Eneloop cells. You would get about twice the run time. And then just swap for a freshly charged set when needed.

Very nice done!

You can order the Lime Audio mics from nohypeaudio. They are very responsive and friendly. And active on audio forums. https://www.nohypeaudio.com Remember that the CM4 can be a bit sensitive to handling noise and a really good suspension and cable relief is needed. Look as rycote lyre 62. Either separate mounted on invision base of choice or the new Invision INV-6 Soft which comes with lyre 62 soft.

You can connect the unlocked iOS device to the USB of a macOS computer, launch QuickTime Player and do being a movie recording and selecting the iOS as source for audio and video. That way you will perform a 1:1 recording of the screen with iOS device system audio. Works well with most apps which do not handle copy protected video like Netflix etc.

It sounds as if the voltage of the battery packs have dropped below the discharge protection voltage. This can happen with packs of being left in stock unsold for a longer time. That might have left the charger unable to begin the process and get the voltage up again. check the battery for a manufacturing date and measure the voltage of it with a multimeter. If it have dropped too low I would not keep them and continue using them but send them back for replacement instead.

I’ve been using Neutriks right angled metal housed 3.5mm connector almost exclusively when soldering my own cables for my mixpre and other audio applications. They are sturdy, easy to solder and put together and low profiled enough. And come in chrome or black. https://www.neutrik.com/en/product/ntp3rc-b

For the Go II it’s a very nice feature indeed. But for being an eventual loophole side stepping the patent with a built in microphone, my theory fails.

Bummer 😀

When I fast skimmed through the saxcom patents I notice this being pretty much repeated through out. audio input port configured to couple to an audio input device But the Rode does not have an input port. They have audio input device directly on/in their device. Could it be that simple that Sax never thought about a built in microphone?