vins

Hi all, I’m looking to make a new cable from my RX12 AES out to Deva 24 for the MRX414 modules. What 4 core + shield /2 pair cable are you using to fit into the Ta5 connectors? I’d rather do this than 2 separate cables. Thanks

Hi all, has anybody successfully Genlocked the Arri mini LF or the Alexa LF from the external timecode source (via Sensor - Genlock - TC In) using something other than Ambient or tentacle sync timecode generators? I’m trying to use my Betso TCX 2+ but I am getting Genlock errors flash up on the camera multiple times during the day and occasionally the 1st AC loses picture. I have swapped to an Ambient system & all appears fine. Thanks Steven

It’s a great piece of kit. On my K-ART I could choose if I wanted to regulate output 1, 2, 4, 5 as an option. I have 1 & 2 regulated only. I think if you are using a power supply you want to have it slightly higher than your battery voltage so when power is connected it chooses the highest voltage which is the power supply. Otherwise it will run the batteries down then swap to the PSU. I’ve always had great service from Antoine too.

Hi, I'm on 2.08. Here's the last part of the Nova facebook thread. Glenn replied a week ago, so they may have only figured it was a bug after your dealings with him. Is the Nova holding date and time? Does the warning happen with every boot or just once? Glenn Sanders We are working on this problem. Seems to be a bug.

Hi, I believe there is a software issue with the internal clock. My Nova fails to pick up the internal clock on occasion but if I restart it, it then picks up the clock. Zaxcom know about it and are trying to fix the issue.

Thanks Karl

Hi Karl, I was wondering if the Duet could be backward compatible like the DSQD to support Digital Hybrid (& IFB modes?) On the cart I am using LT & LR for sends around the set, T4's for IFB and LT's in the bag for IFB & Digital Hybrid sends also. I love the ability to change modes depending of what I want to send where on the LT's. The next step would be to add some M2R's to the kit, for high quality personal feeds. If I could send all these Digital Hybrid/IFB/IEM sends using the M2T that would be amazing. Is this something that would be possible as a firmware update? Even if it was just the Digital Hybrid compatibility. Thanks Steven

Thanks for the info. So that sounds pretty good, bar a couple of things yet to be implemented. I’d love to hear from anybody using the Deva with an Oasis. What does the sound report look like? I’m using movie slate currently but would love to use the Deva sound report if it looks good & there’s a better notes field than the Fusion/ old Devas etc. Is the script import & footswitch still a thing or did that disappear with the Deva 32?

Hi, how are the current users of the Deva 24 finding it? Does everything work as planned / are there things that were don’t work currently? Is anyone using the Deva 24 with an Oasis? Can you use a IPad yet for the Oasis Remote / Mix 16 remote? I haven’t seen any feedback/software updates on the Zaxcom forum although I’m not on Facebook if that where it’s happening. Cheers

Cool. Does this software borrow anything from the Deva 24? I have been in contact with Zaxcom recently about getting the PFL to work on playback with an FP8 so hopefully that makes it into the next software revision.

Hi, yeah I did ask Lectro a while back about a wiring configuration and what they told me didn't work either. I've just had another look at the mute circuit diagram and I think I was missing that the switch looks like it needs 4v from pin 2 I'm guessing that this could be the wiring assuming I can take the 3.3v from the audio signal wire. ta5 pin 1- lemo 1 & shell ta5 pin 2 - lemo 3 ta5 pin 3 - lemo 3 On a Lectro they get this from the servo bias separately so it may not work properly. Also 4v vs 3.3v - hopefully it will be enough to power both the mic and the switch. I think the ground to the shell is just for better RF performance isn't it?

Just reviving this old thread as I'm still looking to use an Zaxcom TRX LT with the Lectrosonics mute switch. Has anybody successfully used the mute switch with another transmitter? I had a cable made with the same wiring as the Lectrosonics MCATA5MLEMO cable which is the adapter cable that Lectro makes to use a ta5 mic with the SSM transmitter with no luck. Does anybody have any thoughts? Cheers Steven

Thanks. I will probably end up getting one of those down the line. What's the estimated RRP? In the meantime, i have a mute and a multiple TRX that could fit the bill with a cable. I was hoping somebody had already made the cable and could advise me on the wiring cheers Steven

Thanks John, all of my wireless are TRX LT. I've edited the original message to include the LT

Hi all, I have in the past used a Lectrosonics Mute switch with a SM/SMD transmitter for boom operator private line communications. I have now switched to all Zaxcom wireless and was wondering if anyone has/is using the mute with a zaxcom trx lt? What wiring is required for the mute to trx lt in place of the Lectrosonics REFUMCABLE? Or alternatively has anyone created a soft switch for a Zaxcom TRX LT? Thanks Steven

My 743 shows full battery on my RX12 meter until it dies also. Battery type set to NiMh QRX on the 743. It sounds like a 743 issue not a 4900 issue Steven

Hi Patrick, do you know what the filter box is called? Is it one of these? GLE-12W thanks

I have had a similar problem with a TRXLT 2.6 pre OLED display. I have had poor range with my rx12 and with lectro SNA600 dipoles as close as 20ft unobstructed in what I thought was a quiet rf area. I have more testing to do but similar results as you. I am interested in what your outcome is.

Sam Kashefi post #205 in the RX12 thread

I use the same case with a couple of additions. I have attached a Velcro strap to go around the pole for safety, and also I have cut/melted a long slit for the aerial to go through. The Velcro is passed under and glued under the belt clip. I use a aerial with a swivel so I can take the transmitter out of the pouch without unscrewing the aerial every time. I use the ambient top tip to get the connector away from the pole and quick release, however I don't think you would be able to have the 742 sideways (so you can access the screen and battery door whilst still on the pole) with a case on. I think it would put too much pressure on the cone and the connector. The last photo shows how tight the fit is sideways. I would prefer to to leave it on the pole to change settings or see the display but more importantly get at the batteries quickly. It looks like I'd have to get a replacement for the top tip. I have left the belt clip on for the odd occasion it will go on the belt. I look forward to seeing any new case designs people come up with

Hi, check you haven't accidentally added a one in the encryption page on the trx or qrx and make sure the tx formats are the same.

Hi, I am looking to add a small 2.4 ghz amplifier to my zaxcom nomad bag/cart rig (when required). I'm looking for something that is small with sma connectors & won't interfere whilst close to everything else and hopefully can be powered through my BDS also. Is anyone successfully using a 500mw or 1w amp in the bag? Also is anyone using a 6v powered version with a step down from their 12v battery? I see a few of the smaller ones are 6v and the larger ones ie 2w plus are 12v Cheers

Hi, I am looking for a new bag for my Nomad, FP8, RX12. I currently have a petrol ps614 but have out grown it with the RX12 addition. I like the look of both of these bags, with some nice design features on both. There is no local Orca retailer here so I can't have a look or fitting with one. Just wondering what bags people are using with this combo and especially if someone has just weighed up one versus the other. Generally it will be used as a bag cart type rig for drama with the ability to go over the shoulder when required. Cheers

Apparently the new versions are really good. I'm yet to test but will hopefully try soon.

I know there was a thread here on the range of the QRX200 which then got the software update to fix the bug which was the signal combining. Was there a similar fix for the QRX100 with older tx that are too old for the XR software? I have used quite a lot of the zax gear with great range (pre XR), in various setups with and without a mic plexer and with shark fins and whips. The dual mode on the QRX100 was the weak link. I understand there should be a drop in range but it wasn't half as good in single mode.