jbuerjes Posted January 28, 2019 Report Share Posted January 28, 2019 11 minutes ago, VAS said: Firmware 3.3 - Current playback: Choose the file - switch play - you hear the file. To exit from playback, you have to go into menu and press "exit from playback". Is there a shortcut or something else to make this routine disappear? Hit play and the file list pops up. That's one step into the menu less. Quote Link to comment Share on other sites More sharing options...
VASI Posted January 30, 2019 Report Share Posted January 30, 2019 On 1/28/2019 at 11:03 PM, jbuerjes said: Hit play and the file list pops up. That's one step into the menu less. Hi Jule, Yeap, that's the way we go to playback mode. To exit from playback mode we have to hit the touchscreen and choose "exit from playback"; that's the problem. PS. Mic preamp and headphone amp from this little machine is amazing. Quote Link to comment Share on other sites More sharing options...
Soundmind Posted February 1, 2019 Report Share Posted February 1, 2019 On 1/29/2019 at 4:49 AM, VAS said: Firmware 3.3 - Current playback: Choose the file - switch play - you hear the file. To exit from playback, you have to go into menu and press "exit from playback". Is there a shortcut or something else to make this routine disappear? In "Rec-ready" mode, toggle the play/rec switch to the left (play) will bring you to file list to choose the track you want to playback. To exit playback mode, toggle the play/ record switch to the right (rec) to return to red-ready mode. Hope it helps Quote Link to comment Share on other sites More sharing options...
Benjamin Posted February 11, 2019 Report Share Posted February 11, 2019 After reaching out to Sonosax again, I've heard back that they've been able to replicate the issue under some conditions. The case has been sent to the hardware engineer, who is quite busy these days/months, presumably with the new preamp/AD. It seems like I'm the only individual who has run up against this, but I'll report back once Sonosax has concluded their investigation. Quote Link to comment Share on other sites More sharing options...
Philip Perkins Posted February 11, 2019 Report Share Posted February 11, 2019 Good for you and good for Sax. There are some issues that really require a lot of persistence to track down. Quote Link to comment Share on other sites More sharing options...
Benjamin Posted March 1, 2019 Report Share Posted March 1, 2019 Sonosax comes through! After looking into this issue, It turns out that the peak occurs due to an odd interaction with a non-stock, modified mike body I've been using. The standard stock body of the microphone presents no such problem. Thanks to the Sonosax team for looking into this. Quote Link to comment Share on other sites More sharing options...
JAX Posted July 10, 2019 Report Share Posted July 10, 2019 SX-LC8+ available now Quote Link to comment Share on other sites More sharing options...
Patrick Tresch Posted September 18, 2019 Report Share Posted September 18, 2019 Good news for DANTE users. The Dante option: announced, postponed, long awaited, it arrives this time for good. Our card now operates according to the criteria we had defined, particularly in terms of consumption. Powered by PoE, it is the least energy consuming on the market and will therefore not shorten the autonomy of your batteries too much. You will be able to connect the multi-channel interface to your SX-AD8+ before the end of the year. The SX-R4+ will have to wait until early 2020 to click its RJ45. https://www.sonosax.ch/sononews-september-2019/ Quote Link to comment Share on other sites More sharing options...
gv970 Posted September 25, 2019 Report Share Posted September 25, 2019 Hi there, I have the SX-R4+ in my wish list, I read all I could find in terms of manuals and few videos on youtube I know nobody in Rome that has one and apparently no dealers or rentals around. What I'm missing are some details about the O/P card It adds 4 aes O/P or 2 balanced O/P or 4 unbalanced but: are those O/P independent from the ones already there? How can I assign them? couldn't find anything online Once installed will I find in the routing menu all these options? How are set the various options? meaning the 4 aes or the 2 balanced or the 4 unbal, it's a menu option or like a dip switch on the card? Thanks Quote Link to comment Share on other sites More sharing options...
JAX Posted September 26, 2019 Report Share Posted September 26, 2019 21 hours ago, gv970 said: Hi there, I have the SX-R4+ in my wish list, I read all I could find in terms of manuals and few videos on youtube I know nobody in Rome that has one and apparently no dealers or rentals around. What I'm missing are some details about the O/P card It adds 4 aes O/P or 2 balanced O/P or 4 unbalanced but: are those O/P independent from the ones already there? How can I assign them? couldn't find anything online Once installed will I find in the routing menu all these options? How are set the various options? meaning the 4 aes or the 2 balanced or the 4 unbal, it's a menu option or like a dip switch on the card? Thanks Hi, here are our answers: "are those O/P independent from the ones already there?" "Once installed will I find in the routing menu all these options?" Yes. The output menu is where you can configure the option outs. See https://www.sonosax.ch/wp-content/uploads/2017/06/audio_outputs.svg "How can I assign them?" The same way you assign any output, monitor out or even mix. See https://www.sonosax.ch/wp-content/uploads/2017/06/monitoring.svg "How are set the various options? for the next steps.meaning the 4 aes or the 2 balanced or the 4 unbal, it's a menu option or like a dip switch on the card?" All configuration is done in the user interface (touch screen). The configuration is done for each output pairs (OPTION 1-2 and 3-4). For 1-2, you can choose BALANCED, UNBALANCED or AES. If you choose BALANCED, OPTION 3-4 is not available. Otherwise, OPTION 3-4 can be configured as UNBALANCED or AES. The block diagram on the option card product page can give you a good idea of that option: https://www.sonosax.ch/product/024281/ Please feel free to contact us for the next steps. https://www.sonosax.ch/contact/ Quote Link to comment Share on other sites More sharing options...
JAX Posted September 26, 2019 Report Share Posted September 26, 2019 Hello, Here the answer of my engineers: "are those O/P independent from the ones already there?" "Once installed will I find in the routing menu all these options?" Yes. The output menu is where you can configure the option outs. See "How can I assign them?" The same way you assign any output, monitor out or even mix. See "How are set the various options? meaning the 4 aes or the 2 balanced or the 4 unbal, it's a menu option or like a dip switch on the card?" All configuration is done in the user interface (touch screen). The configuration is done for each output pairs (OPTION 1-2 and 3-4). For 1-2, you can choose BALANCED, UNBALANCED or AES. If you choose BALANCED, OPTION 3-4 is not available. Otherwise, OPTION 3-4 can be configured as UNBALANCED or AES. The block diagram on the option card product page can give you a good idea of that option: https://www.sonosax.ch/product/024281/ If you need more infos, you can contact: sonosax@sonosax.ch Best, Jacques Quote Link to comment Share on other sites More sharing options...
gv970 Posted September 26, 2019 Report Share Posted September 26, 2019 11 hours ago, JAX said: Hello, Here the answer of my engineers: "are those O/P independent from the ones already there?" "Once installed will I find in the routing menu all these options?" Yes. The output menu is where you can configure the option outs. See "How can I assign them?" The same way you assign any output, monitor out or even mix. See "How are set the various options? meaning the 4 aes or the 2 balanced or the 4 unbal, it's a menu option or like a dip switch on the card?" All configuration is done in the user interface (touch screen). The configuration is done for each output pairs (OPTION 1-2 and 3-4). For 1-2, you can choose BALANCED, UNBALANCED or AES. If you choose BALANCED, OPTION 3-4 is not available. Otherwise, OPTION 3-4 can be configured as UNBALANCED or AES. The block diagram on the option card product page can give you a good idea of that option: https://www.sonosax.ch/product/024281/ If you need more infos, you can contact: sonosax@sonosax.ch Best, Jacques I couldn't wait for a better answer!!! Thanks very much to Mister Sax and his engineers And absolutely great that the SX-R4+ works as I was expecting. It will be mine! cheers Quote Link to comment Share on other sites More sharing options...
JAX Posted September 28, 2019 Report Share Posted September 28, 2019 Your welcome. As we have no distributor in Italy, you can order directly to SONOSAX in Switzerland. Good week end, Jacques Quote Link to comment Share on other sites More sharing options...
VASI Posted September 18, 2020 Report Share Posted September 18, 2020 DANTE Card Available https://www.sonosax.ch/product/024352/ Quote Link to comment Share on other sites More sharing options...
DanieldH Posted April 21, 2021 Report Share Posted April 21, 2021 Sonosax announced a not so super- but minislot module https://www.sonosax.ch/sononews-april-2021/ Quote Link to comment Share on other sites More sharing options...
codyman Posted April 21, 2021 Report Share Posted April 21, 2021 6 minutes ago, DanieldH said: Sonosax announced a not so super- but minislot module https://www.sonosax.ch/sononews-april-2021/ Seems slick, I like the boxiness yet functionality of it. Kind of a bummer it doesn't have an antenna distro though. I do like whatever those heavy duty sma antennas they are using on the SRb though. I wonder where they got those from as I'd be interested a few of those myself! Quote Link to comment Share on other sites More sharing options...
Neil Mc Posted April 22, 2021 Report Share Posted April 22, 2021 19 hours ago, DanieldH said: Sonosax announced a not so super- but minislot module https://www.sonosax.ch/sononews-april-2021/ A thing of beauty! Quote Link to comment Share on other sites More sharing options...
Patrick Tresch Posted April 22, 2021 Report Share Posted April 22, 2021 Jacques told me that he didn't want to put a antenna splitter as it's allways a compromise for best signal unless you use a finn. He also opted not to use the superslot system mainly for size and weight reasons. They worked on the mechanics to make it user friendly. Quote Link to comment Share on other sites More sharing options...
codyman Posted April 22, 2021 Report Share Posted April 22, 2021 I'm curious to know how the 8 fader pots work on that thing. If you're using two analog 2 channel slot receivers, do just the first four pots work? Are they assignable? Quote Link to comment Share on other sites More sharing options...
Patrick Tresch Posted April 22, 2021 Report Share Posted April 22, 2021 They can be assignable through the menu of the SX-R4+ or the 8 series from Sound Devices. Look at it like a remote control like the SX-RC8+. Quote Link to comment Share on other sites More sharing options...
DanieldH Posted April 23, 2021 Report Share Posted April 23, 2021 There was even an announcement in October 2020 with conceptional pics of the sides. https://www.sonosax.ch/sononews-october-2020/ Quote Link to comment Share on other sites More sharing options...
docsound Posted April 28, 2021 Report Share Posted April 28, 2021 On 4/22/2021 at 8:51 PM, Patrick Tresch said: Jacques told me (…) He also opted not to use the superslot system mainly for size and weight reasons. They worked on the mechanics to make it user friendly. How will the receivers be connected to the recorder? Is there a D-sub port inside or just nothing and you need to use some cable like this: https://www.sonosax.ch/product/002357/ Quote Link to comment Share on other sites More sharing options...
DanieldH Posted April 28, 2021 Report Share Posted April 28, 2021 3 hours ago, docsound said: How will the receivers be connected to the recorder? Is there a D-sub port inside or just nothing and you need to use some cable like this: https://www.sonosax.ch/product/002357/ Like that: (connectors are 3M MDR26) Quote Link to comment Share on other sites More sharing options...
docsound Posted April 29, 2021 Report Share Posted April 29, 2021 10 hours ago, DanieldH said: Like that: (connectors are 3M MDR26) Thank you! But I mean how the receivers will be connected inside the RX8? D-sub? Quote Link to comment Share on other sites More sharing options...
DanieldH Posted April 29, 2021 Report Share Posted April 29, 2021 6 hours ago, docsound said: Thank you! But I mean how the receivers will be connected inside the RX8? D-sub? On the video Patrick posted, you can see briefly how Jacques inserts an A10 RX with what should be the DB25 Panasonic/Ikegami style connection. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.