The Post Place
the section for everything relating to Post-Production
356 topics in this forum
-
- 3 replies
- 1.1k views
This is going back in time a little. My friend has 4 DAT tapes that were recorded on a Fostex PD4 at 48kHz, 30 fps non drop. He wants them transferred to a digital computer file that he can edit. On the Audio side, I was planning on using my Fostex Pd4 to transfer from it's AES/EBU digital output via a 110 ohm xlr into my Sound Devices 664's digital input. The 664 would be set to 48kHz/ 24 bit. I would send the Fostex's playback time code into the time code input of the 664. My question is, will this work without me doing anything to alter the playback speed for the file to work when he sinks sound to picture in the computer. His super 16 film was transferred …
Last reply by FILMMIX, -
- 0 replies
- 611 views
This is going back in time so any help will be appreciated. A friend of mine asked me to transfer some dat tapes into non linear digital form so he can edit on a computer. The original dat tapes were recorded on a Fostex pd4 at 48Khz 30 non drop. I am planning on using my old Pd4 and going digital out (110 ohm xlr) to digital in on a sound devices 664. I will send the timecode out from the Fostex to time code in on the 664. My question is do I just transfer from one deck to the other at 48kHz and leave the file to be adjusted on the post production computer? Or should I do something else during the transfer. The picture was shot on super 16 and the negative was transfer…
Last reply by Steve Rogers, -
- 5 replies
- 1.7k views
I've got two different soundbites from a short doc interview. I have attached them to this post. The programs I am using are Adobe Audition for the main edit and then I'll often pull individual pieces into Izotope RX 7. For the first one (TEVIN_366_Fire_Extracted), near the end of the soundbite, he says "...to just go and change my life and that's what I did." As he says "and that's what I did", there is an intense Rustle from the clothing on the lav mic that overwhelms what he's saying. Not sure if this is too far gone or salvageable at all. Then the 2nd one, (TEVIN_366_Nothing_Extracted), when he says "This is nothing.." there is an audible CLI…
Last reply by berniebeaudry, -
- 3 replies
- 2.3k views
I'm hoping someone can answer this question for me? I have an AVID S3 with the Pro Tools Dock/ipad combo for my studio setup at home. Usually, after creating a layout in EuControl, I can then just pressed the lefthand buttons on the S3 to call up my layouts. However, for some reason, now when i press the Layout number, the iPad Control App switches to the proper layout but the S3 does not change the Faders themselves (it's stuck on my DX only tracks. Is there a setting I accidentally set in EuControl Preferences that could have changed this? Scrtching my head.
Last reply by jgbsound, -
- 1 follower
- 1 reply
- 2.1k views
i am wondering if a sync solution exists currently with protools (non-HD version, without option for field recorder sync). a few times a year i post for a client project that i recorded tracks during production. the editor usually starts with my files and gives me an omf export from avid, so my audio files with heads and tails are in his export. this time around a different editor finished the project in premier, and used cam audio. i talked him through an omf export which worked well but i really wanted to use my production sound for this project. I had to manually sync clips. it was a rather short project with a tight turn but in the future i really want to have a bette…
Last reply by franky03, -
- 1 follower
- 11 replies
- 2k views
Hello, Did a scene today with a practical SM58. Didn't amplify it to the room through the speaker until take 3. My question is, how easy is it to fake the speaker sound in post and make it sound realistic? We also had a boom in the room far from the practical, picking up the distant perspective and then the speaker sound once it was powered on. Second question is, how easy is it to make it match the aesthetic we got once we started using the speaker? To make takes 1-2 match the rest. Thanks, Ben
Last reply by BAB414, -
- 5 replies
- 3.1k views
Hello, I am currently doing production sound for a indie feature set in the fifties in an African city. Obviously we struggling to avoid plane, (chinese) motorbikes, modern cars, AC fans, water pumps, amplified call for prayer, to mention only the quotidian ones... I do not think I will get a chance to record enough stereo ambient sound as I usually do because of these issues. I have a fairly number of years of experience in film but this is my first non contemporary era film. So my question is can we rely on post only to re-create ambient sounds, assembling isolated sounds, to get credible soundscapes for the diverse scenes set in town? What a…
Last reply by Mike Westgate, -
- 8 replies
- 2.1k views
Hello soundgroup members, For the people with little to no time here's the Question in short: (longer version is below) I want to create a similar sound to the one that the locket makes in this video (below) every time it gets attacked. Any idea with what I should start ? The only thing I hear is someone eating a cookie. Thanks Thiellie --------------- Here's the same Question a bit longer: I'm a student with 0 experience and interested in creating some sound effects. As my teacher's ears are tired of me asking questions I wanted to try another way to get information on how to do things. For a short film we made in school I…
Last reply by The Immoral Mr Teas, -
- 0 replies
- 1.2k views
Hey y'all. Thought you might be interested in this. Pro Sound Effects have a cheeky little giveaway in a couple of days. The prize is a 1yr sub to Pro Tools Ultimate, Izotope Production Production Suite, some stuff by Krotos, and $4000 worth of samples from PSE. No affiliation, but everyone deserves a copy of RX! I hug mine every night. Pro Sound Effect Giveaway
Last reply by LDstudios, -
- 2 replies
- 1.1k views
I posted this in the computer section also, I hope that's okay, if not, please delete. I have a question for the post production / computer experts here. Our facility runs two ProTools HDX suites for audio post for Television. We mix in stereo only. The audio systems used to be synched to house black with an AVID Sync HD and the video satellite (AVID Media Composer with Mojo DX I/O) is also synched to house black . Since our workflow is entirely file based now I’m not sure if I still need to use the Sync HD and here’s the reason why I’m asking. We bought an IZ Technologies RADAR Studio for our A suite about 2 years ago. It replaced an old MacPro. Tha…
Last reply by Werner Althaus, -
How do YOU deal with them?
Last reply by TVPostSound, -
- 12 replies
- 7k views
Hello everyone, I'm working on an environmental documentary mix and the editor/director did not include all the audio feeds into the timeline edit and resulting AAF. So I am trying to reconstruct the edited version of audio and replace the Lav Feed with the Boom. So I have all the original source RAW interviews that were recorded on location copied onto Temp tracks in the project. Is there any way to "match" by waveforms in Pro Tools 12HD? This would be similar to the way PluralEyes and Premiere Pro matches audio by analyzing waveforms. Ideally, I'd like to pull up some sort of plugin window, select my "Source" samp…
Last reply by TVPostSound, -
- 1 reply
- 945 views
I recorded two lavs and one boom to a Zoom F8 in a remote location. I didn't notice any audio problems when monitoring. On the files, including each iso, there is a 'warble'. It is on some of the tracks, and not others, though set up and location was the same during short interviews. I say this because i don't think the interference came from the microphones, i think it happened in the recorder? I would like to try and fix it, the spectrum analyzer shows deeper dropout from the 'warble' or 'modulated' tracks. I don't know how to research it because i'm not what happened or what to call it. Linden Intermodulated Boom .mp3
Last reply by canyouhearmenow, -
- 18 replies
- 5k views
Hi! I am happy to have found this forum! I have to sync my 50p footage for television to an audio recorder. timecode can only be provided to the camera Via mini jack audio LTC port. As the LTC protocol only allows frame rates up to 30p I can only select 25p in the ultrasync one timecode box. The software then has to interpret this timecode and calculate the timecode for my 50p video. I couldn't do this in avid or davinci resolve, does anyone know a way? I think tentacle sync studio can do exactly this but I don't own it and it is a rather complicated workflow. Does anyone know how to do it in an NLE? especially avid or dr?
Last reply by Sound, -
- 1 reply
- 2.2k views
I am starting a new topic on this as it doest fit into my old post: I just bought a Mixpre 10 II and I am trying to Sync it to my Sony a7 III via two ultrasync one units. So i am converting audio timecode of the video file to Start Timecode and sync it to the timecode of the mixpre 10 II. BUT: The Mixpre 10 II has a file size limit of 4GB because of the SD card recording. So it always splits audio after some time and creates a new file. in 32bit with 10 tracks 48khz its about 37 minutes. So its very likely to have a video file that has to be synced to multiple audio files, but that doesnt seem to work. Avid Media Composer and Davinci Resolve only s…
Last reply by pillepalle, -
- 1 follower
- 4 replies
- 1.2k views
I'm prepping a 2-hour docy that has an important one-shot premiere in a historic theater... in ten days. (Needless to say, it's not locked yet.) Of the two hours, about five minutes has stereo music or sfx. The rest is archive footage and new interviews. The theater can handle DCP, but the producer can't take the time for a lab. He's leaving my studio with a hard drive under his arm, hopping on a plane with the editor and his laptop, and they'll be syncing and compressing as necessary during the flight to the venue. The theater can also take BluRay with AC3, or play a stereo or LCR track with picture from a hard drive. I wan…
Last reply by Mike Westgate, -
- 1 reply
- 823 views
Has anyone else noticed that when you pull up the global clip gain (Shft-Ctrl + -), after you make gain adjustments, sometimes the undo doesn't function? T Sometimes it works, other times ...nada. I was doing a bunch of dialog gain adjustments and did about 10 of them, changed my mind and decided to try and undo them. No luck Chuck. Not sure if it's just me or if others have noticed. OH and btw; I'm using a windows system.
Last reply by TVPostSound, -
- 1 follower
- 7 replies
- 2.2k views
Hello Guys This is KISHOR CHAUHAN An India based Location Sound Mixer has if Now i Had Did Many Documentaries,Short Films,Ad film,Corporate and much more As a Location Sound Mixer. And now i want to be a Part of Post Production and I dont have more Ideas abut Post Production i am beginner in post i jst need a help which Software is More Understanable,Much Easier For Beginner To do Audio Post Production.My Mac already has Pro tools i need to buy plug-in for it i.e Audio cleaning,Hum removal and other.so which is the best.
Last reply by Olle Sjostrom, -
- 9 replies
- 2.8k views
I just received this email from Avid: Important install update regarding Pro Tools products This email is to inform you that Pro Tools 2019.6 (released today) resolves an issue we uncovered where interruptions in internet connectivity can cause Pro Tools | First, Pro Tools, and Pro Tools | Ultimate to delete local (offline) Projects. We escalated this issue with high priority, identified …
Last reply by macformat, -
- 3 replies
- 1.2k views
Hello All, So I'm noticing a weird thing in EuControl when trying to create a layout and assign tracks to it for my S3? Let me preface by saying I run on Windows. I'm able to pull up EuControl from the S3 (Shift + Sel). EuControls Sees Protools (I have my session open with the track's I'd like to add in the Assign page). But in EuControl's Assign tab all channel strips (1-16) which are by default set to auto assigned, won't let me change them. If I click on the dropdown nothing happens! (I have display applications track numbers checked). Further, if I switch to the Layouts tab, it won't let me name my Layout. If…
Last reply by jgbsound, -
- 9 replies
- 4.9k views
Is it possible to batch autosync sound and video using timecode in Premier Pro CS6? I know this can be done in Avid and FCP. There seem to be a merge clip with timecode function in Premier Pro, but this only lets you sync one at a time. What I would like to know is of there is a way to batch sync the files. Sammy Huen
Last reply by Vepus, -
- 1 follower
- 3 replies
- 1.6k views
I did a project this last week and they started first day with no timecode sync. To compound the problem the camera was set to 24 FPS and sound was set to 23.97... Looking to address the frame rate issue only in this thread. Any quick/cheap fixes? Batch processing? Public domain audio file converters? Thanks
Last reply by jpb2, -
- 0 replies
- 1k views
I'm shooting a corporate video and sync the cam by TC. I will also do the post so I want to make sure editing does it right. Problem is, they're shooting on 4.6 K RAW and since the files need to be converted before they go to edit, I'd like to give them some advice as to at what stage audio should ideally be synced with the video files - before/after conversion? Or even sync to proxy video files? If anybody here is familiar with picture editing workflows, any advice would be welcome!
Last reply by Christian Spaeth, -
- 2 followers
- 28 replies
- 10k views
What are some of your favorite plugins for post production, and are any free? I’m getting back into post but since my absence a lot has changed. There are obvious ones like izotope but I’d like to see what the consensus is on others.
Last reply by haifai, -
- 1 follower
- 7 replies
- 8.1k views
Hello, I get asked to mix some very indie projects in 5.1 and somtimes I don’t really see why. If there is nothing but a single boom track and music there really isn’t that much to mix. Is it worth the time to convert those projects to 5.1? I would assume you would at least want some foley/sound fx to really make a difference. Or is it that important to have more music in the back of the theater than the front? Thanks, Louis
Last reply by Brian Liston,